diff --git a/arch/arm/include/asm/arch-tegra/mmc.h b/arch/arm/include/asm/arch-tegra/mmc.h
index 5c95047..71ad407 100644
--- a/arch/arm/include/asm/arch-tegra/mmc.h
+++ b/arch/arm/include/asm/arch-tegra/mmc.h
@@ -22,6 +22,6 @@
 #ifndef _TEGRA_MMC_H_
 #define _TEGRA_MMC_H_
 
-int tegra_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio);
+void tegra_mmc_init(void);
 
 #endif /* _TEGRA_MMC_H_ */
diff --git a/arch/arm/include/asm/arch-tegra/tegra_mmc.h b/arch/arm/include/asm/arch-tegra/tegra_mmc.h
index dd746ca..bd18f5f 100644
--- a/arch/arm/include/asm/arch-tegra/tegra_mmc.h
+++ b/arch/arm/include/asm/arch-tegra/tegra_mmc.h
@@ -27,6 +27,8 @@
 #define TEGRA_SDMMC3_BASE	0xC8000400
 #define TEGRA_SDMMC4_BASE	0xC8000600
 
+#define MAX_HOSTS		4	/* Max number of 'hosts'/controllers */
+
 #ifndef __ASSEMBLY__
 struct tegra_mmc {
 	unsigned int	sysad;		/* _SYSTEM_ADDRESS_0 */
@@ -119,12 +121,15 @@
 
 struct mmc_host {
 	struct tegra_mmc *reg;
+	int id;			/* device id/number, 0-3 */
+	int enabled;		/* 1 to enable, 0 to disable */
+	int width;		/* Bus Width, 1, 4 or 8 */
+	enum periph_id mmc_id;	/* Peripheral ID: PERIPH_ID_... */
+	struct fdt_gpio_state cd_gpio;		/* Change Detect GPIO */
+	struct fdt_gpio_state pwr_gpio;		/* Power GPIO */
+	struct fdt_gpio_state wp_gpio;		/* Write Protect GPIO */
 	unsigned int version;	/* SDHCI spec. version */
 	unsigned int clock;	/* Current clock (MHz) */
-	unsigned int base;	/* Base address, SDMMC1/2/3/4 */
-	enum periph_id mmc_id;	/* Peripheral ID: PERIPH_ID_... */
-	int pwr_gpio;		/* Power GPIO */
-	int cd_gpio;		/* Change Detect GPIO */
 };
 
 #endif	/* __ASSEMBLY__ */
diff --git a/board/avionic-design/common/tamonten.c b/board/avionic-design/common/tamonten.c
index e6a932e..ea95e43 100644
--- a/board/avionic-design/common/tamonten.c
+++ b/board/avionic-design/common/tamonten.c
@@ -33,13 +33,8 @@
 #include <asm/arch/tegra.h>
 #include <asm/arch-tegra/board.h>
 #include <asm/arch-tegra/clk_rst.h>
-#include <asm/arch-tegra/mmc.h>
 #include <asm/arch-tegra/sys_proto.h>
 #include <asm/arch-tegra/uart.h>
-#ifdef CONFIG_TEGRA_MMC
-#include <mmc.h>
-#endif
-
 
 #ifdef CONFIG_BOARD_EARLY_INIT_F
 void gpio_early_init(void)
@@ -54,7 +49,7 @@
  * Routine: pin_mux_mmc
  * Description: setup the pin muxes/tristate values for the SDMMC(s)
  */
-static void pin_mux_mmc(void)
+void pin_mux_mmc(void)
 {
 	funcmux_select(PERIPH_ID_SDMMC4, FUNCMUX_SDMMC4_ATB_GMA_GME_8_BIT);
 	/* for write-protect GPIO PI6 */
@@ -62,16 +57,4 @@
 	/* for CD GPIO PH2 */
 	pinmux_tristate_disable(PINGRP_ATD);
 }
-
-/* this is a weak define that we are overriding */
-int board_mmc_init(bd_t *bd)
-{
-	/* Enable muxes, etc. for SDMMC controllers */
-	pin_mux_mmc();
-
-	/* init dev 0, SD slot, with 4-bit bus */
-	tegra_mmc_init(0, 4, GPIO_PI6, GPIO_PH2);
-
-	return 0;
-}
 #endif
diff --git a/board/compal/paz00/paz00.c b/board/compal/paz00/paz00.c
index 1447f47..d6e5c37 100644
--- a/board/compal/paz00/paz00.c
+++ b/board/compal/paz00/paz00.c
@@ -18,19 +18,14 @@
 #include <asm/io.h>
 #include <asm/arch/tegra.h>
 #include <asm/arch/pinmux.h>
-#include <asm/arch-tegra/mmc.h>
 #include <asm/gpio.h>
-#ifdef CONFIG_TEGRA_MMC
-#include <mmc.h>
-#endif
-
 
 #ifdef CONFIG_TEGRA_MMC
 /*
  * Routine: pin_mux_mmc
  * Description: setup the pin muxes/tristate values for the SDMMC(s)
  */
-static void pin_mux_mmc(void)
+void pin_mux_mmc(void)
 {
 	/* SDMMC4: config 3, x8 on 2nd set of pins */
 	pinmux_set_func(PINGRP_ATB, PMUX_FUNC_SDIO4);
@@ -51,25 +46,6 @@
 	/* For CD GPIO PV5 */
 	pinmux_tristate_disable(PINGRP_GPV);
 }
-
-/* this is a weak define that we are overriding */
-int board_mmc_init(bd_t *bd)
-{
-	debug("board_mmc_init called\n");
-
-	/* Enable muxes, etc. for SDMMC controllers */
-	pin_mux_mmc();
-
-	debug("board_mmc_init: init eMMC\n");
-	/* init dev 0, eMMC chip, with 8-bit bus */
-	tegra_mmc_init(0, 8, -1, -1);
-
-	debug("board_mmc_init: init SD slot\n");
-	/* init dev 3, SD slot, with 4-bit bus */
-	tegra_mmc_init(3, 4, GPIO_PV1, GPIO_PV5);
-
-	return 0;
-}
 #endif
 
 #ifdef CONFIG_LCD
diff --git a/board/compulab/trimslice/trimslice.c b/board/compulab/trimslice/trimslice.c
index 8f4dd09..8401100 100644
--- a/board/compulab/trimslice/trimslice.c
+++ b/board/compulab/trimslice/trimslice.c
@@ -27,12 +27,8 @@
 #include <asm/arch/clock.h>
 #include <asm/arch/funcmux.h>
 #include <asm/arch/pinmux.h>
-#include <asm/arch-tegra/mmc.h>
 #include <asm/gpio.h>
 #include <i2c.h>
-#ifdef CONFIG_TEGRA_MMC
-#include <mmc.h>
-#endif
 
 void pin_mux_usb(void)
 {
@@ -52,7 +48,7 @@
  * Routine: pin_mux_mmc
  * Description: setup the pin muxes/tristate values for the SDMMC(s)
  */
-static void pin_mux_mmc(void)
+void pin_mux_mmc(void)
 {
 	funcmux_select(PERIPH_ID_SDMMC1, FUNCMUX_SDMMC1_SDIO1_4BIT);
 	funcmux_select(PERIPH_ID_SDMMC4, FUNCMUX_SDMMC4_ATB_GMA_4_BIT);
@@ -60,20 +56,3 @@
 	/* For CD GPIO PP1 */
 	pinmux_tristate_disable(PINGRP_DAP3);
 }
-
-/* this is a weak define that we are overriding */
-int board_mmc_init(bd_t *bd)
-{
-	debug("board_mmc_init called\n");
-
-	/* Enable muxes, etc. for SDMMC controllers */
-	pin_mux_mmc();
-
-	/* init dev 0 (SDMMC4), (micro-SD slot) with 4-bit bus */
-	tegra_mmc_init(0, 4, -1, GPIO_PP1);
-
-	/* init dev 3 (SDMMC1), (SD slot) with 4-bit bus */
-	tegra_mmc_init(3, 4, -1, -1);
-
-	return 0;
-}
diff --git a/board/nvidia/common/board.c b/board/nvidia/common/board.c
index 665fa1c..babbe08 100644
--- a/board/nvidia/common/board.c
+++ b/board/nvidia/common/board.c
@@ -48,6 +48,9 @@
 #ifdef CONFIG_USB_EHCI_TEGRA
 #include <asm/arch-tegra/usb.h>
 #endif
+#ifdef CONFIG_TEGRA_MMC
+#include <asm/arch-tegra/mmc.h>
+#endif
 #include <i2c.h>
 #include <spi.h>
 #include "emc.h"
@@ -221,3 +224,25 @@
 #endif
 	return 0;
 }
+
+#if defined(CONFIG_TEGRA_MMC)
+void __pin_mux_mmc(void)
+{
+}
+
+void pin_mux_mmc(void) __attribute__((weak, alias("__pin_mux_mmc")));
+
+/* this is a weak define that we are overriding */
+int board_mmc_init(bd_t *bd)
+{
+	debug("%s called\n", __func__);
+
+	/* Enable muxes, etc. for SDMMC controllers */
+	pin_mux_mmc();
+
+	debug("%s: init MMC\n", __func__);
+	tegra_mmc_init();
+
+	return 0;
+}
+#endif
diff --git a/board/nvidia/harmony/harmony.c b/board/nvidia/harmony/harmony.c
index 93430ed..3122441 100644
--- a/board/nvidia/harmony/harmony.c
+++ b/board/nvidia/harmony/harmony.c
@@ -27,19 +27,14 @@
 #include <asm/arch/funcmux.h>
 #include <asm/arch/pinmux.h>
 #include <asm/arch/tegra.h>
-#include <asm/arch-tegra/mmc.h>
 #include <asm/gpio.h>
-#ifdef CONFIG_TEGRA_MMC
-#include <mmc.h>
-#endif
-
 
 #ifdef CONFIG_TEGRA_MMC
 /*
  * Routine: pin_mux_mmc
  * Description: setup the pin muxes/tristate values for the SDMMC(s)
  */
-static void pin_mux_mmc(void)
+void pin_mux_mmc(void)
 {
 	funcmux_select(PERIPH_ID_SDMMC4, FUNCMUX_SDMMC4_ATB_GMA_GME_8_BIT);
 	funcmux_select(PERIPH_ID_SDMMC2, FUNCMUX_SDMMC2_DTA_DTD_8BIT);
@@ -54,25 +49,6 @@
 	/* For CD GPIO PI5 */
 	pinmux_tristate_disable(PINGRP_ATC);
 }
-
-/* this is a weak define that we are overriding */
-int board_mmc_init(bd_t *bd)
-{
-	debug("board_mmc_init called\n");
-
-	/* Enable muxes, etc. for SDMMC controllers */
-	pin_mux_mmc();
-
-	debug("board_mmc_init: init SD slot J26\n");
-	/* init dev 0, SD slot J26, with 8-bit bus */
-	tegra_mmc_init(0, 8, GPIO_PI6, GPIO_PH2);
-
-	debug("board_mmc_init: init SD slot J5\n");
-	/* init dev 2, SD slot J5, with 4-bit bus */
-	tegra_mmc_init(2, 4, GPIO_PT3, GPIO_PI5);
-
-	return 0;
-}
 #endif
 
 void pin_mux_usb(void)
diff --git a/board/nvidia/seaboard/seaboard.c b/board/nvidia/seaboard/seaboard.c
index 3e33da0..e581fdd 100644
--- a/board/nvidia/seaboard/seaboard.c
+++ b/board/nvidia/seaboard/seaboard.c
@@ -28,11 +28,7 @@
 #include <asm/arch/funcmux.h>
 #include <asm/arch/gpio.h>
 #include <asm/arch/pinmux.h>
-#include <asm/arch-tegra/mmc.h>
 #include <asm/gpio.h>
-#ifdef CONFIG_TEGRA_MMC
-#include <mmc.h>
-#endif
 
 /* TODO: Remove this code when the SPI switch is working */
 #if !defined(CONFIG_SPI_UART_SWITCH) && (CONFIG_MACH_TYPE != MACH_TYPE_VENTANA)
@@ -51,7 +47,7 @@
  * Routine: pin_mux_mmc
  * Description: setup the pin muxes/tristate values for the SDMMC(s)
  */
-static void pin_mux_mmc(void)
+void pin_mux_mmc(void)
 {
 	funcmux_select(PERIPH_ID_SDMMC4, FUNCMUX_SDMMC4_ATB_GMA_GME_8_BIT);
 	funcmux_select(PERIPH_ID_SDMMC3, FUNCMUX_SDMMC3_SDB_4BIT);
@@ -61,25 +57,6 @@
 	/* For CD GPIO PI5 */
 	pinmux_tristate_disable(PINGRP_ATC);
 }
-
-/* this is a weak define that we are overriding */
-int board_mmc_init(bd_t *bd)
-{
-	debug("board_mmc_init called\n");
-
-	/* Enable muxes, etc. for SDMMC controllers */
-	pin_mux_mmc();
-
-	debug("board_mmc_init: init eMMC\n");
-	/* init dev 0, eMMC chip, with 8-bit bus */
-	tegra_mmc_init(0, 8, -1, -1);
-
-	debug("board_mmc_init: init SD slot\n");
-	/* init dev 1, SD slot, with 4-bit bus */
-	tegra_mmc_init(1, 4, GPIO_PI6, GPIO_PI5);
-
-	return 0;
-}
 #endif
 
 void pin_mux_usb(void)
diff --git a/board/nvidia/whistler/whistler.c b/board/nvidia/whistler/whistler.c
index 592cd6b..f18aa27 100644
--- a/board/nvidia/whistler/whistler.c
+++ b/board/nvidia/whistler/whistler.c
@@ -27,32 +27,19 @@
 #include <asm/arch/clock.h>
 #include <asm/arch/funcmux.h>
 #include <asm/arch/pinmux.h>
-#include <asm/arch-tegra/mmc.h>
 #include <asm/gpio.h>
 #include <i2c.h>
+
 #ifdef CONFIG_TEGRA_MMC
-#include <mmc.h>
-#endif
-
-
 /*
  * Routine: pin_mux_mmc
  * Description: setup the pin muxes/tristate values for the SDMMC(s)
  */
-static void pin_mux_mmc(void)
-{
-	funcmux_select(PERIPH_ID_SDMMC3, FUNCMUX_SDMMC3_SDB_SLXA_8BIT);
-	funcmux_select(PERIPH_ID_SDMMC4, FUNCMUX_SDMMC4_ATC_ATD_8BIT);
-}
-
-/* this is a weak define that we are overriding */
-int board_mmc_init(bd_t *bd)
+void pin_mux_mmc(void)
 {
 	uchar val;
 	int ret;
 
-	debug("board_mmc_init called\n");
-
 	/* Turn on MAX8907B LDO12 to 2.8V for J40 power */
 	ret = i2c_set_bus_num(0);
 	if (ret)
@@ -70,17 +57,10 @@
 	if (ret)
 		printf("i2c_write 0 0x3c 0x44 failed: %d\n", ret);
 
-	/* Enable muxes, etc. for SDMMC controllers */
-	pin_mux_mmc();
-
-	/* init dev 0 (SDMMC4), (J29 "HSMMC") with 8-bit bus */
-	tegra_mmc_init(0, 8, -1, -1);
-
-	/* init dev 1 (SDMMC3), (J40 "SDIO3") with 8-bit bus */
-	tegra_mmc_init(1, 8, -1, -1);
-
-	return 0;
+	funcmux_select(PERIPH_ID_SDMMC3, FUNCMUX_SDMMC3_SDB_SLXA_8BIT);
+	funcmux_select(PERIPH_ID_SDMMC4, FUNCMUX_SDMMC4_ATC_ATD_8BIT);
 }
+#endif
 
 /* this is a weak define that we are overriding */
 void pin_mux_usb(void)
diff --git a/board/toradex/colibri_t20_iris/colibri_t20_iris.c b/board/toradex/colibri_t20_iris/colibri_t20_iris.c
index e40a986..aa76f65 100644
--- a/board/toradex/colibri_t20_iris/colibri_t20_iris.c
+++ b/board/toradex/colibri_t20_iris/colibri_t20_iris.c
@@ -19,7 +19,6 @@
 #include <asm/arch/funcmux.h>
 #include <asm/arch/pinmux.h>
 #include <asm/arch-tegra/board.h>
-#include <asm/arch-tegra/mmc.h>
 
 #include "../colibri_t20-common/colibri_t20-common.h"
 
@@ -34,13 +33,13 @@
 #endif
 
 #ifdef CONFIG_TEGRA_MMC
-int board_mmc_init(bd_t *bd)
+/*
+ * Routine: pin_mux_mmc
+ * Description: setup the pin muxes/tristate values for the SDMMC(s)
+ */
+void pin_mux_mmc(void)
 {
 	funcmux_select(PERIPH_ID_SDMMC4, FUNCMUX_SDMMC4_ATB_GMA_4_BIT);
 	pinmux_tristate_disable(PINGRP_GMB);
-
-	tegra_mmc_init(0, 4, -1, GPIO_PC7);
-
-	return 0;
 }
 #endif
diff --git a/drivers/mmc/tegra_mmc.c b/drivers/mmc/tegra_mmc.c
index 7258619..455a690 100644
--- a/drivers/mmc/tegra_mmc.c
+++ b/drivers/mmc/tegra_mmc.c
@@ -2,7 +2,7 @@
  * (C) Copyright 2009 SAMSUNG Electronics
  * Minkyu Kang <mk7.kang@samsung.com>
  * Jaehoon Chung <jh80.chung@samsung.com>
- * Portions Copyright 2011-2012 NVIDIA Corporation
+ * Portions Copyright 2011-2013 NVIDIA Corporation
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
@@ -21,6 +21,7 @@
 
 #include <bouncebuf.h>
 #include <common.h>
+#include <fdtdec.h>
 #include <asm/gpio.h>
 #include <asm/io.h>
 #include <asm/arch/clock.h>
@@ -28,44 +29,14 @@
 #include <asm/arch-tegra/tegra_mmc.h>
 #include <mmc.h>
 
-/* support 4 mmc hosts */
-struct mmc mmc_dev[4];
-struct mmc_host mmc_host[4];
+DECLARE_GLOBAL_DATA_PTR;
 
+struct mmc mmc_dev[MAX_HOSTS];
+struct mmc_host mmc_host[MAX_HOSTS];
 
-/**
- * Get the host address and peripheral ID for a device. Devices are numbered
- * from 0 to 3.
- *
- * @param host		Structure to fill in (base, reg, mmc_id)
- * @param dev_index	Device index (0-3)
- */
-static void tegra_get_setup(struct mmc_host *host, int dev_index)
-{
-	debug("tegra_get_setup: dev_index = %d\n", dev_index);
-
-	switch (dev_index) {
-	case 1:
-		host->base = TEGRA_SDMMC3_BASE;
-		host->mmc_id = PERIPH_ID_SDMMC3;
-		break;
-	case 2:
-		host->base = TEGRA_SDMMC2_BASE;
-		host->mmc_id = PERIPH_ID_SDMMC2;
-		break;
-	case 3:
-		host->base = TEGRA_SDMMC1_BASE;
-		host->mmc_id = PERIPH_ID_SDMMC1;
-		break;
-	case 0:
-	default:
-		host->base = TEGRA_SDMMC4_BASE;
-		host->mmc_id = PERIPH_ID_SDMMC4;
-		break;
-	}
-
-	host->reg = (struct tegra_mmc *)host->base;
-}
+#ifndef CONFIG_OF_CONTROL
+#error "Please enable device tree support to use this driver"
+#endif
 
 static void mmc_prepare_data(struct mmc_host *host, struct mmc_data *data,
 				struct bounce_buffer *bbstate)
@@ -518,41 +489,43 @@
 
 	debug("tegra_mmc_getcd called\n");
 
-	if (host->cd_gpio >= 0)
-		return !gpio_get_value(host->cd_gpio);
+	if (fdt_gpio_isvalid(&host->cd_gpio))
+		return fdtdec_get_gpio(&host->cd_gpio);
 
 	return 1;
 }
 
-int tegra_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio)
+static int do_mmc_init(int dev_index)
 {
 	struct mmc_host *host;
 	char gpusage[12]; /* "SD/MMCn PWR" or "SD/MMCn CD" */
 	struct mmc *mmc;
 
-	debug(" tegra_mmc_init: index %d, bus width %d "
-		"pwr_gpio %d cd_gpio %d\n",
-		dev_index, bus_width, pwr_gpio, cd_gpio);
-
+	/* DT should have been read & host config filled in */
 	host = &mmc_host[dev_index];
+	if (!host->enabled)
+		return -1;
+
+	debug(" do_mmc_init: index %d, bus width %d "
+		"pwr_gpio %d cd_gpio %d\n",
+		dev_index, host->width,
+		host->pwr_gpio.gpio, host->cd_gpio.gpio);
 
 	host->clock = 0;
-	host->pwr_gpio = pwr_gpio;
-	host->cd_gpio = cd_gpio;
-	tegra_get_setup(host, dev_index);
-
 	clock_start_periph_pll(host->mmc_id, CLOCK_ID_PERIPH, 20000000);
 
-	if (host->pwr_gpio >= 0) {
+	if (fdt_gpio_isvalid(&host->pwr_gpio)) {
 		sprintf(gpusage, "SD/MMC%d PWR", dev_index);
-		gpio_request(host->pwr_gpio, gpusage);
-		gpio_direction_output(host->pwr_gpio, 1);
+		gpio_request(host->pwr_gpio.gpio, gpusage);
+		gpio_direction_output(host->pwr_gpio.gpio, 1);
+		debug(" Power GPIO name = %s\n", host->pwr_gpio.name);
 	}
 
-	if (host->cd_gpio >= 0) {
+	if (fdt_gpio_isvalid(&host->cd_gpio)) {
 		sprintf(gpusage, "SD/MMC%d CD", dev_index);
-		gpio_request(host->cd_gpio, gpusage);
-		gpio_direction_input(host->cd_gpio);
+		gpio_request(host->cd_gpio.gpio, gpusage);
+		gpio_direction_input(host->cd_gpio.gpio);
+		debug(" CD GPIO name = %s\n", host->cd_gpio.name);
 	}
 
 	mmc = &mmc_dev[dev_index];
@@ -567,9 +540,9 @@
 
 	mmc->voltages = MMC_VDD_32_33 | MMC_VDD_33_34 | MMC_VDD_165_195;
 	mmc->host_caps = 0;
-	if (bus_width == 8)
+	if (host->width == 8)
 		mmc->host_caps |= MMC_MODE_8BIT;
-	if (bus_width >= 4)
+	if (host->width >= 4)
 		mmc->host_caps |= MMC_MODE_4BIT;
 	mmc->host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS | MMC_MODE_HC;
 
@@ -578,8 +551,6 @@
 	 *  low-speed SDIO card frequency (actually 400KHz)
 	 * max freq is highest HS eMMC clock as per the SD/MMC spec
 	 *  (actually 52MHz)
-	 * Both of these are the closest equivalents w/216MHz source
-	 *  clock and Tegra SDMMC divisors.
 	 */
 	mmc->f_min = 375000;
 	mmc->f_max = 48000000;
@@ -588,3 +559,95 @@
 
 	return 0;
 }
+
+/**
+ * Get the host address and peripheral ID for a node.
+ *
+ * @param blob		fdt blob
+ * @param node		Device index (0-3)
+ * @param host		Structure to fill in (reg, width, mmc_id)
+ */
+static int mmc_get_config(const void *blob, int node, struct mmc_host *host)
+{
+	debug("%s: node = %d\n", __func__, node);
+
+	host->enabled = fdtdec_get_is_enabled(blob, node);
+
+	host->reg = (struct tegra_mmc *)fdtdec_get_addr(blob, node, "reg");
+	if ((fdt_addr_t)host->reg == FDT_ADDR_T_NONE) {
+		debug("%s: no sdmmc base reg info found\n", __func__);
+		return -FDT_ERR_NOTFOUND;
+	}
+
+	host->mmc_id = clock_decode_periph_id(blob, node);
+	if (host->mmc_id == PERIPH_ID_NONE) {
+		debug("%s: could not decode periph id\n", __func__);
+		return -FDT_ERR_NOTFOUND;
+	}
+
+	/*
+	 * NOTE: mmc->bus_width is determined by mmc.c dynamically.
+	 * TBD: Override it with this value?
+	 */
+	host->width = fdtdec_get_int(blob, node, "bus-width", 0);
+	if (!host->width)
+		debug("%s: no sdmmc width found\n", __func__);
+
+	/* These GPIOs are optional */
+	fdtdec_decode_gpio(blob, node, "cd-gpios", &host->cd_gpio);
+	fdtdec_decode_gpio(blob, node, "wp-gpios", &host->wp_gpio);
+	fdtdec_decode_gpio(blob, node, "power-gpios", &host->pwr_gpio);
+
+	debug("%s: found controller at %p, width = %d, periph_id = %d\n",
+		__func__, host->reg, host->width, host->mmc_id);
+	return 0;
+}
+
+/*
+ * Process a list of nodes, adding them to our list of SDMMC ports.
+ *
+ * @param blob          fdt blob
+ * @param node_list     list of nodes to process (any <=0 are ignored)
+ * @param count         number of nodes to process
+ * @return 0 if ok, -1 on error
+ */
+static int process_nodes(const void *blob, int node_list[], int count)
+{
+	struct mmc_host *host;
+	int i, node;
+
+	debug("%s: count = %d\n", __func__, count);
+
+	/* build mmc_host[] for each controller */
+	for (i = 0; i < count; i++) {
+		node = node_list[i];
+		if (node <= 0)
+			continue;
+
+		host = &mmc_host[i];
+		host->id = i;
+
+		if (mmc_get_config(blob, node, host)) {
+			printf("%s: failed to decode dev %d\n",	__func__, i);
+			return -1;
+		}
+		do_mmc_init(i);
+	}
+	return 0;
+}
+
+void tegra_mmc_init(void)
+{
+	int node_list[MAX_HOSTS], count;
+	const void *blob = gd->fdt_blob;
+	debug("%s entry\n", __func__);
+
+	count = fdtdec_find_aliases_for_id(blob, "sdhci",
+		COMPAT_NVIDIA_TEGRA20_SDMMC, node_list, MAX_HOSTS);
+	debug("%s: count of sdhci nodes is %d\n", __func__, count);
+
+	if (process_nodes(blob, node_list, count)) {
+		printf("%s: Error processing mmc node(s)!\n", __func__);
+		return;
+	}
+}
diff --git a/include/fdtdec.h b/include/fdtdec.h
index c7a92d5..32730d2 100644
--- a/include/fdtdec.h
+++ b/include/fdtdec.h
@@ -71,6 +71,7 @@
 	COMPAT_NVIDIA_TEGRA20_NAND,	/* Tegra2 NAND controller */
 	COMPAT_NVIDIA_TEGRA20_PWM,	/* Tegra 2 PWM controller */
 	COMPAT_NVIDIA_TEGRA20_DC,	/* Tegra 2 Display controller */
+	COMPAT_NVIDIA_TEGRA20_SDMMC,	/* Tegra SDMMC controller */
 	COMPAT_NVIDIA_TEGRA20_SFLASH,	/* Tegra 2 SPI flash controller */
 	COMPAT_NVIDIA_TEGRA20_SLINK,	/* Tegra 2 SPI SLINK controller */
 	COMPAT_SMSC_LAN9215,		/* SMSC 10/100 Ethernet LAN9215 */
diff --git a/lib/fdtdec.c b/lib/fdtdec.c
index 7c7fc83..000130f 100644
--- a/lib/fdtdec.c
+++ b/lib/fdtdec.c
@@ -46,6 +46,7 @@
 	COMPAT(NVIDIA_TEGRA20_NAND, "nvidia,tegra20-nand"),
 	COMPAT(NVIDIA_TEGRA20_PWM, "nvidia,tegra20-pwm"),
 	COMPAT(NVIDIA_TEGRA20_DC, "nvidia,tegra20-dc"),
+	COMPAT(NVIDIA_TEGRA20_SDMMC, "nvidia,tegra20-sdhci"),
 	COMPAT(NVIDIA_TEGRA20_SFLASH, "nvidia,tegra20-sflash"),
 	COMPAT(NVIDIA_TEGRA20_SLINK, "nvidia,tegra20-slink"),
 	COMPAT(SMSC_LAN9215, "smsc,lan9215"),